绝对压力变送器的规格代码说明
型号
规格代码
说明
ATE-E310A
绝对压力变送器
输出信号
-E······
4～20mA,HART协议数字通讯（参见GS1C22T2-CY）
测量量程
（膜盒）
L·······
M·······
H·······
V···············
0.67～10kPa{5～75mmHg}abs
1.3～130kPa{9.6～960mmHg}abs
0.03～3MPa{0.3～30Kgf/cm2}abs
接液部分材质
S····················
H····················
M····················
T····················
A····················
D····················
B····················
SCS14A(注1)SUS316L(注2)SUS316
螺栓、螺母材质
0···················
1···················
2···················
3···················
4···················
5···················
L膜盒M膜盒A膜盒
SCM43510kPaabs130kPaabs3MPaabs
{75mmHgabs}{960mmHgabs}{30kgf/cm2abs}
SUS63010kPaabs130kPaabs3MPaabs
{75mmHgabs}{960mmHgabs}{30kgf/cm2abs}
SUH66010kPaabs130kPaabs3MPaabs
安装方式
2··················
4··················
6··················
垂直安装，右面高压，过程接头在上（注3）
垂直安装，右面高压，过程接头在下（注3）
垂直安装，左面高压，过程接头在上（注3）
垂直安装，左面高压，过程接头在下（注3）
水平安装，右面高压（注4）
水平安装，左面高压（注4）
接线口
-2·················
-3·················
-6·················
-7·················
-8·················
-9·················
G1/2内螺纹，1处接线口
1/2NPT内螺纹，2处接线口Pg13.5内螺纹，2处接线口
M20内螺纹，2处接线口
G1/2内螺纹，2处接线口，带一个盲塞
1/2NPT内螺纹，两个电气接口，一个盲塞Pg13.5内螺纹，两个电气接口，一个盲塞
M20内螺纹，两个电气接口，一个盲塞
显示表头
0·················
2·················
3·················
4·················
数字式表头
带设定按钮的数字表头
（无表头）
2-inch安装支架
G···············
H···············
J···············
D···············
E··············
SECC平托架
SUS304平托架
SECCL型托架
SUS304L型托架
无安装支架
例：ATE-E220A-EMSA12G5A-92NN
注1：低压侧接液部分材质：容室法兰：SCS14A，管道连接件：SCS14A膜合：SUS316L（隔离膜片：哈氏合金C-276）排气螺钉：SUS316
注2：仅适用4-inch(100mm，DN100)法兰（法兰尺寸/材质代码：“G”或“H”“J”）注3：仅适用于3-inch(80mm，DN80)法兰（法兰尺寸/材质代码：“D”或“E”“F”）※记号是标准规格中最具代表